Netgear WNAP320 Guida Utente Pagina 95
- Pagina / 126
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Chapter 5. Advanced Configuration | 95
ProSafe Wireless-N Access Point WNAP320 Reference Manual
For example, first configure security profile NETGEAR-WDS-1 with the MAC address
of AP1, and then configure security profile NETGEAR-WDS-2 with the MAC address
of AP3 (see Figure 57 on p
age 92).
2. Activate repe
ater mode on the wireless access point (AP2 in Figure 57 on page 92):
a. On th
e Bridging screen, select the Enable Wireless Bridging check box.
b. Select
the Wireless Point-to-Multi-Point Bridge radio button.
c. Clear th
e Enable Wireless Client Association check box to disable wireless client
association (see the red circle in Figure 58 o
n page 93).
Note: If you do not clear the Enable Wireless Client Association check box,
the wireless access point will not function in repeater mode but in
point-to-multipoint bridge mode.
d. If the correct profile names and security options are displayed in the table, select the
check boxes in the Enable column for all security profiles that you want to enable.
e. Click Apply in th
e Bridging screen to activate your repeater settings.
3. Conf
igure AP1 on LAN Segment 1 (see Figure 57 on page 92) in repeater mode with the
remote MAC address of AP2.
4. Conf
igure AP3 on LAN Segment 3 (see Figure 57 on page 92) in repeater mode with the
remote MAC address of AP2.
5. V
erify the following for all wireless access points:
• All APs must be
on the same LAN, that is, the LAN IP addresses of all APs must be in
the same network as the LAN devices.
• If you use DHCP
, all wireless access points must obtain an IP address automatically
(as a DHCP client). For more information, see Configure IP Settings and Optional
DHCP Server Settings on page 21.
• All wireless a
ccess points must use the same channel, authentication mode, and
security settings.
6. V
erify connectivity across the LANs:
• A compute
r on any LAN segment should be able to connect to the Internet or share
files and printers with any other PCs or servers connected to any of the two LAN
segments.
Note: You can extend the repeating functionality by adding up to two more
wireless access points that are configured in repeater mode.
However, since repeaters communicate in half-duplex mode, the
bandwidth decreases as you add repeaters to the network. Also, you
can extend the range of the wireless network with NETGEAR
wireless antenna accessories.
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Revision History 2
- Contents 3
- Chapter 4 Management 4
- Chapter 6 Troubleshooting 4
- Contents 5
- Introduction 6
- What Is In the Box? 7
- System Requirements 7
- Key Features and Standards 7
- Key Features 8
- Hardware Description 10
- Top Panel 11
- Rear Panel 12
- Figure 3 13
- Ethernet Cabling Requirements 15
- Figure 4 17
- Web Management Interface 18
- Figure 7 19
- Figure 8 19
- Figure 9 20
- To configure the IP settings: 21
- 1. Select Con 21
- Figure 11 22
- Table 5. LAN Settings 23
- Figure 12 24
- Ceiling Installation 28
- 5. Conn 29
- Wall Installation 30
- 4. Conn 31
- Desk Installation 33
- Figure 13 35
- Security Profiles 36
- Figure 14 39
- Figure 15 40
- Figure 16 44
- Figure 17 44
- Configure Legacy 802.1X 45
- Figure 20 46
- Figure 21 46
- • WPA-PSK 47
- • WPA2-PSK 47
- • WPA-PSK & WPA2-PSK 47
- Figure 25 48
- 3. Click App 49
- Figure 26 50
- Schedule the Wireless Radio 52
- Figure 28 53
- Management 55
- SNMP Management 56
- Figure 30 57
- Figure 31 57
- Web Browser Upgrade Procedure 59
- TFTP Server Upgrade Procedure 59
- Defaults 60
- Restore the Configuration 61
- Settings 62
- Default Configuration 63
- Figure 37 64
- Figure 38 64
- Enable the Syslog Server 65
- View System Information 66
- Monitor Wireless Stations 68
- Figure 42 69
- View the Activity Log 70
- Traffic Statistics 71
- Figure 45 73
- Figure 46 74
- Field Description 75
- Advanced Configuration 76
- Figure 47 77
- Hotspot Settings 78
- Figure 49 79
- Figure 50 82
- Table 24. EDCA Settings 83
- Configure Wireless Bridging 84
- Figure 51 85
- Figure 52 86
- Figure 53 86
- Figure 54 88
- Figure 55 89
- Figure 56 89
- Figure 57 92
- Figure 58 93
- Figure 59 93
- Figure 60 96
- Troubleshooting 97
- Basic Functioning 98
- Wireless-Capable Computer 99
- Problems with Date and Time 103
- Use the Packet Capture Tool 103
- Supplemental Information 105
- Technical Specifications 106
- Factory Default Settings 107
- Command-Line Reference 109
- Notification of Compliance 117
- FCC Caution 118
- Industry Canada statement: 118
- Radiation Exposure Statement: 118
- Interference Reduction Table 120
- Numerics 121
- 122 122
- Index 123
- 124 124
- Index 125
- 126 126
Prodotti e manuali riguardandi Punti d’accesso WLAN Netgear WNAP320
Punti d’accesso WLAN Netgear WNDAP620 Manuale Utente
(172 pagine)
(172 pagine)
(70 pagine)
Punti d’accesso WLAN Netgear WAG102 Manuale Utente
(102 pagine)
(102 pagine)
Punti d’accesso WLAN Netgear 802.11g Manuale Utente
(108 pagine)
(108 pagine)
Punti d’accesso WLAN Netgear WG602v2 Guida Utente
(122 pagine)
(122 pagine)
Punti d’accesso WLAN Netgear MP115 Guida Utente
(78 pagine)
(78 pagine)
Pfister 016-FE0K manuály
Uživatelské manuály a uživatelské příručky pro Příslušenství pro vodu Pfister 016-FE0K.
Poskytujeme 1 manuály pdf Pfister 016-FE0K ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commenti su questo manuale